Fridge Evaporator Door Handle - White Stock Number: ES1495238
Genuine spare part for select models of LEC fridge freezers
Overall rating
Product Reviews
Write a review-
Matt W. Marlow
-
John Soar Brighton5.0 out of 5
Fitting handle 04 February 2023
It's easier to take the freezer door off. Put the spindle in to the handle first. The unbroken edge is the edge that connects to the latch on the fridge, the other edge has 2 teeth & acts as a spring. You'll notice that on the door, by the holes that the spindle fits in to, there are 2 tiny cut outs, this is where the spindle fits in to. Push the spindle along the cut outs & it will clip in to place.
Ease of fitting 2.0 out of 5 Quality 4.0 out of 5 Value 3.0 out of 5 -
JayCee Biggin Hill Kent5.0 out of 5
To Fit - easy when you know how 17 November 2022
1) It's important that you work from the back and the side of the door of the freezer section 2) Fit the spindle/spring contraption in the handle first 3) The long part of the spring fits in the 2 lugs on the main part of the fridge 4) Make sure then that the long part of the spring is slightly protruding from the handle and that the 2 smaller lengths of plastic are up against the door 5) Fit the spindle/spring into main door of the freezer section lining up the 2 holes pushing upwards 6) Then turn the handle flush with the freezer door and it will click into position 7) You will note that there is a slight gradient on the door by the bottom hole to allow it to do so. So when it happens again I shall visit this site, read my instructions and hope they make sense! I hope this helps.
Ease of fitting 1.0 out of 5 Quality 5.0 out of 5 Value 5.0 out of 5 -
CB Isle of Skye5.0 out of 5
Correct Part 13 January 2022
Easy to identify part required for make & model of fridge and received very promptly. Fitting of freezer box handle was a bit fidgety and took several attempts and a bit of patience. Good result. Thank you espares.
Ease of fitting 3.0 out of 5 Quality 5.0 out of 5 Value 4.0 out of 5 -
roy Salisbury5.0 out of 5
Fitting 30 May 2018
I found the best way to fit the door handle was first to remove the evaporator door. Then remove the broken handle and the catch fitting. This can be done with a pull on the handle to remove the male part from the female part. Next fit the new handle to the original catch by inserting the handle the top of the catch then pushing the lower open part into the catch. With a little prising the handle /catch fitting can be inserting into the door housing. Refit the door.
Ease of fitting 3.0 out of 5 Quality 5.0 out of 5 Value 5.0 out of 5 -
Diana Bilson France5.0 out of 5
Good replacement part 18 April 2018
This was a good quality, replacement part for our LEC fridge freezer door. It was not very easy to fit, and we doubt we could ever do it again! Perseverance is the name of the game once you have established the correct way to fit it with the spindle. It helped to find a picture on this site of a similar replacement handle with the spindle in situ. As always we received excellent service and advice prior to purchasing.
Ease of fitting 2.0 out of 5 Quality 5.0 out of 5 Value 5.0 out of 5 -
adrian Tunbridge wells5.0 out of 5
very good service 20 March 2018
web was easy to use to find the product wanted and the delivery was good
Ease of fitting 5.0 out of 5 Quality 5.0 out of 5 Value 5.0 out of 5 -
K T5.0 out of 5
First Purchase 18 December 2017
This is my first purchase fro e-spares and I found the item good quality and easy to fit.
Ease of fitting 5.0 out of 5 Quality 5.0 out of 5 Value 5.0 out of 5 -
Bill J5.0 out of 5
once fitted - great. but difficult to fit 01 November 2017
First make sure that you are fitting the spindle and catch the right way round! Duuh - but I did not the first time. If you can, look at the door carefully before taking the old handle off the door and as you dismantle it (or take pics on phone). Finally - try running hot water over the assembly for a while before fitting. For me this softened the plastic enough to make pressing the bits together MUCH easier.
Ease of fitting 2.0 out of 5 Quality 5.0 out of 5 Value 5.0 out of 5 -
John Potts Dereham5.0 out of 5
Good but fiddly 18 October 2017
Good quality lever. Just a bit fiddly to fit but easy after a few minutes to work out method. Very pleased.
Ease of fitting 3.0 out of 5 Quality 5.0 out of 5 Value 5.0 out of 5
Ratings-Only Reviews
Overall Rating | 2.0 stars | 2.0 |
---|---|---|
Ease of fitting | 1.0 stars | 1.0 |
Quality | 4.0 stars | 4.0 |
Value | 1.0 stars | 1.0 |
Based on the average of 1 ratings-only reviews
Will this part fit my appliance?
Check Now- In Stock Available for immediate despatch
- Delivery Available About delivery
- We won't be beaten on price Price match guarantee
Perfect replacement part 21 April 2023
Received this part and a little fiddly to fit but is exactly what I needed. When installing ensure you clip the plastic rod into the handle first. Then at an angle attach the handle to the bottom lug first in the door. Then with a small screw driver and slight pressure, push the top of the plastic rod down so it clips into the top lug. It will with a little force clip in.