Dishwasher Detergent Dispenser Assembly Stock Number: ES478542

Overall rating

• sd essex
  4.0 out of 5

  works as it says 17 April 2015

  Need torx driver to fit which most people do not have

  Ease of fitting	3.0 out of 5
  Quality	4.0 out of 5
  Value	3.0 out of 5

• Anonymous
  4.0 out of 5

  Really useful instruction video 07 August 2014

  The instruction video was really useful. I'm not particularly dexterous and this was the first time I'd replaced a dishwasher soap dispenser so it took me a while to do the job. However, it saved me money and time in not having to get a man in - so well worth the effort.

  Ease of fitting	3.0 out of 5
  Quality	5.0 out of 5
  Value	5.0 out of 5

• enge4952 Berkshire
  4.0 out of 5

  Dispensing advice............. 09 June 2012

  The dispenser arrived without instructions as to how to fit it, but I found a couple of videos on the e-Spares site showing how to fit a dispenser (although not a Zanussi, so the process was challenging). The item is not cheap, but it does the job and works better than the old one.

  Quality	5.0 out of 5
  Value	3.0 out of 5
  Ease of fitting	4.0 out of 5

• m
  4.0 out of 5

  Easy 26 October 2011

  Only needed the door from it so seemed expensive as took the door off and fitted it to the old dispenser. Quick and easy though.

  Quality	4.0 out of 5
  Value	2.0 out of 5
  Ease of fitting	4.0 out of 5

• taffyterry Blakedown
  4.0 out of 5

  Panicy plumber 15 March 2011

  Very quickly delivered, Looked completely different. Instruction about electric refering to unheard of bits and what should be done with them. Needed coffee with a shot. Sat down - and relooked at website video -- and the little grey cells took over. Courage up - took 15 mins to remove old piece and refit new and have the machine tested and running perfectly. Had another shot as reward. Simplicity itself - Thank you E-spares .. it was the video that worked for me

  Quality	5.0 out of 5
  Value	5.0 out of 5
  Ease of fitting	4.0 out of 5

• s Busselton Western Austral
  4.0 out of 5

  Replacing the soap / rinse aid dispenser 28 November 2010

  Having experienced difficulty obtaining a replacement cutlery basket for our AEG dishwasher I had already discovered the e-spares web site, so when the catch on the rinse aid dispenser broke I went on line to look for a replacement. Fortunately the site links to a video demonstrating how to make the switch as it is not obvious how the unit is removed. The video explains the process clearly and the unit is almost the same as the one it replaces. The AEG dishwasher is slightly different to the one in the video which from memory is a Bosch. Consequently the front of the door wants to fall off during the process which caused momentary concern. The wiring connections for the new unit are also slightly different and I was not 100% confident I had understood the instructions in this regard until I turned the unit back on and it worked. The adaptor is the wire at the bottom of the picture. It would have been easier with a second pair of hands to hold the door whilst performing removal and reattachment.Fitting is straightforward and only required phillips head screwdriver and pliers for a stiff connector. For someone who does not usually disassemble dishwashers there was a degree of anxiety until completion but this is actually straightforward. When the door front falls off there is a risk to the wiring which spans the inner and outer parts of the door.

  Quality	5.0 out of 5
  Value	3.0 out of 5
  Ease of fitting	3.0 out of 5

• Lovesoapy Essex
  4.0 out of 5

  Works well 31 January 2010

  I had a Zanussi dishwasher and the wash cycle would often finish with the soap tablet lying forlornly at the bottom unused. You have to remove the door panel (lay screws out carefully and be careful of the sharp edges!)Mark the electrical fittings as L and R before removing. It is easy to fit and then lots of screwing. It appears to have worked fine.

  Quality	4.0 out of 5
  Value	4.0 out of 5
  Ease of fitting	3.0 out of 5

Ratings-Only Reviews