Get The App From Play Store!

Skip to main content

Microwave Turntable Motor Stock Number: ES132365

Genuine spare part for select models of Panasonic microwaves

Product Q&A

Ask a Question

I have a Panasonic NN A574SB Quartz Grill Combi Microwave Oven Stainless Steel 271 1000W

By Anonymous - Salisbury - 19 January 2012
  • The electrical shielding offered by this plate is critical to safety - mircowaves heat flesh as well as food, so know the risk before proceeding. Search YouTube which has plenty of guiding videos. The design is such that you need to snip the thin metal between the holes at the perimiter of the plate in order to remove it. It goes back rotated 180 degrees with tabs locating on one side and use a self-tapping screw on the other side. By Anonymous - - 21 September 2013
  • I only broke 3/4 of the tabs and used the others as a hinge. refix by hinging down and bend tabs to hold in place. if not use some duct tape By Anonymous - Merseyside - 22 February 2012
Answer this question
By Lars - - 28 July 2010
  • ia this motor with panasonic model nn-a574 By kamlesh desai - uk - 21 November 2013
  • Don't know whether it is OK for all Panasonic's but would guess it probably is. Easy to install once you have worked out how. By Ro, - - 08 June 2011
Answer this question
By Amit - - 20 November 2018
  • eSpares Staff from eSpares
    eSpares Staff at eSpares says...

    You have to use the correct part and rating for the model.

Answer this question
By SP - - 18 January 2018
  • Chris from eSpares
    Chris at eSpares says...

    The coupler should be released once the motor is out as it needs to move slightly 'off center' but will be held by the motor shaft.

Answer this question
By KT - - 26 May 2016
  • Chris from eSpares
    Chris at eSpares says...

    As this is an AC motor the wires can be reversed on the motor without issue. Some motors will rotate clockwise and when stopped may run anti clockwise.

Answer this question

I have accessed the motor from the cover panel under the microwave. All seemed straight forward until I started to try and remove the screws that hold the motor in place. The screws turn and turn and turn but are not releasing the motor. Any suggestions?

By John M - Preston, Lanc's UK - 21 January 2016
  • Chris from eSpares
    Chris at eSpares says...

    The screws are not the best quality and if over tightened when fitting will have probably stripped the thread on the cavity or screw. To remove use one screwdriver to apply pressure levering the motor away as you unscrew the screws. Once started the screws will often 'bite' and start to unscrew.

Answer this question
By R Hayward-Crisp - waterlooville Hants - 18 October 2015
  • Chris from eSpares
    Chris at eSpares says...

    The motor has a high resistance and will not show if you are measuring on a low resistance range use the higher resistance ranges. It also has a high gear ratio drive so should be difficult to turn. Check the coupling to the turntable is not cracked allowing it to slip when driven, see our article: How to replace a turntable motor www.espares.co.uk/advice/5/147

Answer this question

we are using this motor to power a small turntable in a display not in a microwave thank you

By mike clark - lowestoft uk. - 18 May 2015
  • Chris from eSpares
    Chris at eSpares says...

    For a 'project' like this i would simply solder the wires directly onto the motor. The small 'spade terminals' may be difficult to obtain but you could try a car spares supplier.

Answer this question

Both motors seem similar, with the same spec. there is a huge difference in price!

By Jopes - Co. Down - 19 February 2015
  • Chris from eSpares
    Chris at eSpares says...

    The motors may be Identical but we have no way of knowing. We would recommend using the correct motor if in doubt.

Answer this question

Motor is TYJ50-8A7 synchronous motor 4W

By Dan - - 27 December 2014
  • Chris from eSpares
    Chris at eSpares says...

    The motor should be between 12 and 20 k ohms typically so your motor appears to have failed.

Answer this question

Will this part fit my appliance?

Check Now

Microwave Turntable Motor

11.48
(inc. VAT)
11.48