Zanussi Magnetic Freezer Door Seal Stock Number: ES1370083

Overall rating

• D.M.
  4.0 out of 5

  Very happy with my purchase 12 September 2018

  I've ordered Magnetic Freezer Door Seal and I am happy with my purchase. It was not so easy to fit it in, but that was mostly because the metal had a bit of rust and therefore had lost the original shape. Otherwise the seal works quite well; surely it is not as good as the original one , but that could have been expected. The life of my freezer has been prolonged now.

  Ease of fitting	4.0 out of 5
  Quality	4.0 out of 5
  Value	4.0 out of 5

• Bob
  4.0 out of 5

  Not as easy as the video suggests 01 October 2017

  This was bought specifically for a Zanussi model but there were no fitting instructions with the delivery. Scouring the eSpares and other videos gave me some idea but the job required some nimble agility. I had assumed that as a magnetic seal it did not need to be seated in a slot but this was wrong. So it took a long time to clear the slots when I worked out where it was to go. However, more caution needs to be emphasised as being too hasty with the Stanley knife can hack at the slot itself. Contrarily you need to work at trimming as much of the old seal as possible,. Easiest done when the main bit is off. I also found a need for fine tweezers (to get bits out that were stuck in the slot), and an small screwdriver to work in the corners which were tight. Also to run down the slots to clean them (wrapped in an antiseptic wipe). Seems to be OK now, but time will tell, I suspect I may need to return to adjust it over time,

  Ease of fitting	2.0 out of 5
  Quality	3.0 out of 5
  Value	3.0 out of 5

• Milo H Snowdonia, Wales
  4.0 out of 5

  Tricky to fit 07 March 2017

  The new seal was needed for the freezer door of a John Lewis fridge freezer. The most helpful advice for both the removal of the old seal & the fitting of the new one was found online. The leaflet accompanying the new seal was misleading. In the end we had to taken the doors off the unit, cut out the soft part & the magnetic strips from the old seal, fit the new one - lots of pushing & easing in needed - then reassemble the doors. Once done, the replacement seal works well.

  Ease of fitting	2.0 out of 5
  Quality	5.0 out of 5
  Value	3.0 out of 5

• bill Folkestone
  4.0 out of 5

  Good quality product 09 October 2014

  Very quick service by next day delivery. Easier to fit than the last one from 4 years ago, but would advise anyone fitting to work the corners into the rim first.

  Ease of fitting	3.0 out of 5
  Quality	5.0 out of 5
  Value	4.0 out of 5

• Boggle Hertfordshire
  4.0 out of 5

  Does the job 28 November 2013

  Not hard to fit, though you have to be a bit careful not to pinch or fold the internal rubber flaps. If you do, you can feel the slight lump as you run you finger round the face of the seal. Clipped in better than the fridge seal, no glue needed. Very little frosting up now.

  Ease of fitting	4.0 out of 5
  Quality	5.0 out of 5
  Value	4.0 out of 5

• Julie London
  4.0 out of 5

  Good product 05 January 2013

  Arrived quickly even over a holiday period. However in box instructions are horrendous! No idea what I was meant to do - hard part removal yes or no? However videos were great and after taking a knife to the old seal the new one was easy ish to fit. Some issue with corners and a little deceptive on whether it was locking in, so fingers crossed

  Quality	4.0 out of 5
  Value	5.0 out of 5
  Ease of fitting	4.0 out of 5

• Anonymous isle of wight
  4.0 out of 5

  cheaper than a new fridge 24 January 2012

  Overall very happy with the result the instructions are a bit vague about fitting but once you've cut the old one off its plane sailing.

  Quality	4.0 out of 5
  Value	4.0 out of 5
  Ease of fitting	4.0 out of 5

Ratings-Only Reviews