Washing Machine Door Interlock. ZV446E for WA135UK Stock Number: ES548529
Spare part suitable for select models of Indesit, Ariston and Hotpoint washing machines
Indesit IWME126. Door locked, all lights flashing. Does anyone know whether buying only the washing machine door interlock part is enough? Do I need an engineer to check circuit board? Opened machine to release the door by pushing down on the door catch 1 Answer
-
Chris at eSpares says...
Just because the door does not open does not always point to a faulty door lock as if the machine recognises a 'fault' then it will often lock the door. Check what is working after restarting and see our video as you may not be able to replace the control module if it is needed. http://www.espares.co.uk/advice/7/1793/how-to-diagnose-washing-machine-control-and-program-problems
Rory mentioned a video to show you how to remove a door that is stuck. Can you tell me where that is? 1 Answer
-
Chris at eSpares says...
You can find it on our advice centre at: http://www.espares.co.uk/advice/7/1294/how-to-open-a-washing-machine-door-thats-stuc or on our you tube channel.
I think my door interlock needs replaced, your video shows removing the clip to get the rubber seal off. If my rubber seal has no clip should I just force it out? Any tips as it feels very tight and a flat head screw driver is not budging it!
-
Christopher at eSpares says...
On Indesit machines the door seal is fixed to the front panel by a retaining band like the one shown in Stock Number: ES831870. This has a spring (often at the bottom or hinge side). use a small screwdriver on this spring to start to pull off. for more details check our video: How to replace the door seal on a washing machine - Hotpoint
- the part you are talking about dose not get sold as a spare part, you can only buy it from indeset as part of the whole unit for £40, but you can buy wire connectors that you crimp for under £1 a packet as ive just found out had same prob bought the door inter lock and still not working tryed everywhere for other part to no avail till some nice man in a electrical shop let me into the secret even supplyed the 3 connectors for free there that cheap https://learn.sparkfun.com/tutorials/working-with-wire/how-to-crimp-an-electrical-connector. this is link will show exact thing i mean
i have a hotpoint aquarius washing machine when switched on the door lock comes on and it does not start it also clicks as if the door is open
-
Chris at eSpares says...
Depending on model this problem could be motor brushes (dismantle examine and replace if required) or a control board problem. If it looks like a control board problem consider a fixed price repair as the board will almost certainly require programming which requires expensive extra parts.
creda excel 1200 vw Hi I need the part on the door the little catch has snapped off. does the interlock come with that part as well ? The part on the machine is fine, I need the part on the actual door, the part with the hook witch goes into the lock, If you know what I mean. thanks
-
Chris at eSpares says...
It sounds like you require the door catch or latch. Enter your full model number to identify the part.
Physically it looks OK, but I can't be sure if the fault is with the lock or with something else, maybe a fuse somewhere? There was a "bang" before the machine went "technical".
- from my experience the machine wont start if the interlock is faulty as it will think the door is open.
wires element in door has burnt out have purchased new door lock part how do i fit it and rewire it 1 Answer
- I've had the same issue happen to me. Although the terminals in the plug looked black and burnt out when I plugged the cable into the new internal door lock it worked fine. The fault was within the actual door lock not the cable. hope this helps.
The door lock wont light up on my hotpoint WD440 so the machine wont start. I have changed the door interlock and the door locks ok but the light wont come on thus it wont start the machine. Any ideas?
- Try checking the brushes on the motor. If you have had the machine some time the brushes can ebcome worn and give these symptoms. (I had the same and it was easily fixed by changing the brushes.)
Hi , my washing machine doesnt start its WMA22 . when you press start it goes to program active indicator light and then to the door lock that starts flashing and it does not start any advise please
- needs new interlock, sensor burnt out
Will this part fit my appliance?
Check Now