Get The App From Play Store!

Skip to main content

Tumble Dryer Rear Drum Bearing Stock Number: ES865498

High quality spare part suitable for select models of Hotpoint, Indesit and Ariston tumble dryers

Read more

Manufactured by Original Quality Component

(This part fits select models)

Will this part fit my Appliance?

Does it fit?
Enter your model number and select from the below list
Need help finding your appliance model number?

Check this part fits your appliance

2. Enter your model number

High Quality Replacement Tumble Dryer Rear Drum Bearing

If your tumble dryer is not turning as it should then it could be that the bearings are faulty, don't worry eSpares could have just the part to get you going again. We have this replacement drum rear teardrop bearing that once fitted to your tumble dryer and you can be sure of getting a better drying performance leaving you with dry clothes again!

Compatible spare part suitable for select models of Hotpoint, Indesit and Ariston tumble dryers.

Please check the suitable model fit list to ensure that this is the correct part for your appliance.

Ask a Question

10 Questions and 12 Answers

This part has worn through on my tuble dryer - question is should there originally have been some ball bearing between the shaft and this part? I can see the sfaft of the drum does have a thinner bit where balls may have sat? Thanks

By nleather1 - - 25 July 2011
  • If the hole in the teardrop bearing has elongated towards the bottom and the dryer has recently been more noisey you may just need to change the teardrop bearing without the need to change the shaft. To check if the shaft is okay, accurately measure the bearing retaining self tapping screw hole from the centre, then mark and drill a new temporary hole for the self tapping retaining screw the same distance from the centre but 180 degrees opposite the original hole, this will enable you to rotate the bearing around 180 degrees so the elongated part is now near the top and the shaft will rest on the unworn part of the bearing. If the dryer then works with no drum noise then the shaft is okay and you just need a new teardrop bearing. By GB - - 12 November 2016
  • Can I just add that the shaft part that looks like it has had ball bearings in, actually looks like that because it has worn a groove in it because it has gone right through the bearing part itself into the casing. So you will need a new shaft also. By SimonT - - 28 November 2011
  • no this part is made to wear By Richi - Ireland - 29 July 2011
Answer this question

hello i was wondering if this fits in the square bearing bracket or is it retained by a bolt / rivet in the smaller hole ? thanks Enda

By enda - leeds - 02 August 2009
  • No. There are two types of bearing, the one pictured and the square version - they are not interchangeable. By Redbrick - Yate - 08 November 2013
  • this part fits with great ease, two screws to remove the bearing cover, then one screw through the small hole, take around five minutes to remove and fit. By ianoliver48 - scottish borders - 26 November 2009
Answer this question

I have worn out my bearing at the rear of my vtd00g. I see the bearing replacement kit and a new belt and the bearing housing, however, where does this bearing go? Thanks

By Frantic - Manchester - 30 July 2009
  • this is not a replacement for a carbon bearing, this fits on the end of the shaft. By ianoliver48 - scottish borders - 26 November 2009
  • the bearing goes on the rear back cover there is one hole were it fits through and the shaft on the rear of the drum goes in the bearing hole By gaz36 - london - 25 September 2009
Answer this question
By AWM - Oban - 04 February 2016
  • Chris from eSpares
    Chris at eSpares says...

    If this bearing has worn through the drum shaft is likely to be damaged and require replacing. If your dryer has three screw heads showing in the centre of the drum kit Stock Number: ES546701 is suitable. If there are no screws showing you will require a kit specifically for the riveted type drum shafts Stock Number: ES1672507 order the correct type for your dryer.

Answer this question
By gravy - mid wales - 30 October 2014
  • Chris from eSpares
    Chris at eSpares says...

    See the video now attached to this part. Try removing the belt of the motor and checking it rotates easily when moved by hand.

Answer this question
See all questions and answers

Will this part fit my appliance?

Check Now

Tumble Dryer Rear Drum Bearing

9.66
(inc. VAT)
9.66