Get The App From Play Store!

Skip to main content

Dishwasher Door Lock Latch Assembly Stock Number: ES509247

Spare part suitable for select models of Hotpoint, Indesit and Ariston dishwashers

Read more

Manufactured by Electruepart

(This part fits select models)

Will this part fit my Appliance?

Does it fit?
Enter your model number and select from the below list
Need help finding your appliance model number?

Check this part fits your appliance

2. Enter your model number

Dishwasher Door Lock Assembly

If you are washing the dishes yourself after dinner time, all because of a damaged door lock to your dishwasher, eSpares can put the situation right. We have this replacement door lock that could soon get your door securely locked, ready for the washing cycle.

With help from eSpares, you can soon be back to being able to relax after meal times - and let the dishwasher do all the hard work!

Spare part suitable for select models of Hotpoint, Indesit and Ariston dishwashers.

Please check the suitable model fit list to ensure that this is the correct part for your appliance.

Ask a Question

12 Questions and 24 Answers

By neilcarpenter - Torquay - 17 February 2009
  • yes it does,my broken one lost spring and pin By ethelsouth33 - hampshire - 08 May 2010
  • Yes Neil this is a complete item ready to fit By Kenjtay - Devon - 23 April 2010
  • Yes By partsfitter - Northumberland - 21 April 2010
  • If you mean the coiled spring holding the latch in place then yes. When fitting look how the existing one fits into the "n" shaped groove and edit the extra plastic (gently) until the new one does the same. By Hearnshaw - Bronte Country - 05 April 2010
  • Yes ,spring included By gammon83 - Wirral - 05 April 2010
  • The switch assembly is the same as the one you remove it contains the housing, the spring and the power switch By emjo - Southport Merseyside - 24 February 2010
  • spring included and easy to fit By ksmakem - kingston upon thames - 18 February 2010
  • yes the spring is included By jobsworth - Bolton - 19 February 2009
Answer this question

I have a DWF50 and am worried that removing this internal panel may damage the detergent release catch

By minilady - wolves - 06 April 2009
  • not sure on that model,on mine just took out top four screws and two either side.carefully pull top front and steel inner apart. WARNING mind fingers on edge of inner panel.sharp took chunk out of finger. By ethelsouth33 - hampshire - 08 May 2010
  • No inner panel stays in place only the top door plastics need removing. Top 8 screws will do the trick. By Kenjtay - Devon - 23 April 2010
  • You shouldn't need to remove the internal panel to fit this. The screws along the inner edge should release the outer plasic cover only. Note the 2 different threads on the screws and make sure they go back in the same place. By Hearnshaw - Bronte Country - 05 April 2010
  • The dishwasher that I repaired (haier) reqired removal of eight philips head screws to give enough acess to the switch then remove the two screws that hold the switch th the door inner, release and lift out the switch assembly remove the two power wires and refit the new switch in the reverse order. Remember to isolate the power before comensing work. By emjo - Southport Merseyside - 24 February 2010
  • I didnt think so but after fitting my new lock something must have happened as it doesnt release anymore By ksmakem - kingston upon thames - 18 February 2010
  • When you remove all the panel screws its only the outercover on the door that comes off, you dont disturb any of the detergent release catch, hinges etc, the job takes about 15 min! By ipol - Glasgow - 18 April 2009
Answer this question
By Nicki - Essex - 10 June 2014
  • Chris from eSpares
    Chris at eSpares says...

    No the catch is Stock Number: ES830831

Answer this question

Have replaced the dock lock, but have been unable to find the spring which broke off from the previous lock. Is it OK to use the dishwasher or do I have to keep searching for the spring?

By Ossie - Kent - 07 May 2014
  • Chris from eSpares
    Chris at eSpares says...

    It is always recommended to remove any loose parts and they could damage wiring or electronic components. If you have removed the door skin and cannot locate the spring check around the control board and switches. If this is ok then you must use with caution at your own risk.

Answer this question
By Anonymous - Middlesbrough - 10 December 2013
  • Chris from eSpares
    Chris at eSpares says...

    The old catch should be alright to use if undamaged, examine carefully and replace if required.

Answer this question
See all questions and answers

Will this part fit my appliance?

Check Now

Dishwasher Door Lock Latch Assembly

12.68
(inc. VAT)
12.68