Skip to main content

Vacuum Cleaner Brushbar Assembly Stock Number: ES1085028

4.8 out of 5 4.8 out of 5 (33 Reviews)

Vacuum Cleaner Brushbar Assembly - ES1085028
View video

4.8 out of 5 4.8 out of 5 (33 Reviews)

Genuine spare part for all models of Dyson DC24 vacuum cleaners

Read more

Manufactured by Dyson

(This part fits select models)

Will this part fit my Appliance?

Does it fit?
Need help finding your appliance model number?

Will this part fit my Appliance?

This product is compatible with:

  • Dyson DC24 Vacuum Cleaners

Vacuum Cleaner Brushbar Assembly

This brushroll is made of tough ABS plastic with long nylon brushes to ensure good deep cleaning when you vacuum. Replacing a damaged brush roll will improve the performance of your vacuum cleaner. So if yours is tangled up with hair or generally worn then pick up this genuine Dyson spare!

Fits all models in the following Dyson vacuum cleaner ranges:

  • DC24

Please check the list of suitable models to ensure that this spare part will fit your appliance.

Dyson spares reference: 917390-01

Write a review

Here’s what other people are saying about Vacuum Cleaner Brushbar Assembly.

(33 reviews)

4.8 out of 5

Ease of fitting 5 out of 5
Quality 5 out of 5
Value 4 out of 5
  • Devon
    5.0 out of 5

    Works

    Just push firmly into place to make sure it engages. No problems.

    Ease of fitting 5.0 out of 5
    Quality 5.0 out of 5
    Value 5.0 out of 5
  • Aberdeenshire Scotland
    5.0 out of 5

    Dyson Hoover parts

    As said before great service I would recommend this company use them all the time

    Ease of fitting 5.0 out of 5
    Quality 5.0 out of 5
    Value 5.0 out of 5
  • Warrington
    5.0 out of 5

    Perfect and easy to fit

    Great service, ordered on line Sunday and received delivery Monday

    Ease of fitting 5.0 out of 5
    Quality 5.0 out of 5
    Value 4.0 out of 5
See all reviews
Ask a Question

6 Questions and 7 Answers

The 3 rubber prongs on the in side of the brush bar has worn away if I replace it will the brush turn again?

By Small - - 16 September 2013
  • If the brush motor is still running then it is the moulded threads but if the brush motor is not running then it is most likely the filters need changing. By Nigel - Wales - 06 October 2019
  • The molded "threads" on the inner side of the end cap that retains the brush bar are easily damaged (usually by trying to remove it without turning it 90 degrees). This allows endways movement of the bar. This extra clearance causes the drive to slip and the drive prongs wear away the corresponding brush bar "prongs" you mention. A new bar will therefore quickly wear the same way without a new end cap. By Keith - Wiltshire - 20 November 2013
Answer this question
By Karen Morgan-Hill - - 27 December 2017
  • Chris from eSpares
    Chris at eSpares says...

    This part is supplied as in the images.

Answer this question
By N W - Devon - 27 October 2015
  • Chris from eSpares
    Chris at eSpares says...

    We are sorry but do not have any dimensions for this product. It is likely the bristles will wear and if used a lot we would suggest replacing it.

Answer this question

Developed a strong vibration from the brush bar area. Found that the housing on the left side end cap (looking from the back of hoover) which fits into the brush bar had fractured. Replaced the end cap and cleaned out the end of the brush bar, albeit the end was rather rough I suspect due to the previously mentioned damaged. Whilst the end cap did turn when fitted onto the brush bar it certainly did not swing freely as shown on the Dyson replacement video. After hoovering half a room the vibration returned and examination revealed that the housing on the end cap had sheared again. Before I purchase a new brush bar and another end cap am I on the right lines or is there some other issue I am not picking up on? Grateful for any advise you can give me

By Scotty - Edinburgh - 06 November 2014
  • Chris from eSpares
    Chris at eSpares says...

    It sounds like the brush spindle may be damaged and if this has resulted in the moulding that located the bearing becoming worn and loose if this is not repaired as well the problem is likely to return. Examine and replace any worn damaged or suspect parts to prevent the chance of future failure.

Answer this question
By gary - glasgow - 11 September 2013
  • Joshua from eSpares
    Joshua at eSpares says...

    If the brush bar is especially worn or if there's anything wrapped round out (such as hair or carpet fibres) then it can cause problems and noise, so take a look. If your vacuum is also producing a burning smell during use then it could be a problem with the motor - check out our video on how to replace it.

Answer this question
See all questions and answers

Will this part fit my appliance?

Check Now

Vacuum Cleaner Brushbar Assembly

19.33
19.33